Skip to the tool
Speaker Cleaner

How to Clean Phone Speaker

A complete walkthrough for the bottom speaker and the earpiece. Read the steps first, then come back to the cleaner when you reach the sound steps.

200Hz

Ready

60seconds left

A rising sweep from 200 to 1200 Hz that shakes loose dry dust and lint. 60 seconds.

Set volume to maximum, turn off silent mode, and hold the phone with the speaker facing down.

Disconnect Bluetooth headphones first, otherwise the sound plays there instead of the phone speaker.

Check the result

Play each side. A clean speaker sounds clear and equally loud on both channels.

What you need before you start

  • A soft dry toothbrush or a soft makeup brush
  • Low-tack painter's tape or cleaning putty
  • A dry microfiber cloth
  • A flashlight, which can be a second phone
  • A cloth lightly dampened with fresh water, only if the phone is sticky or got wet
  • A phone with the case off and Bluetooth disconnected

How long a clean takes

A routine clean takes about five minutes: a minute of brushing, 60 seconds of Dust mode, a minute or two of dabbing with tape, and a quick test. If the phone is very dirty, plan for a second round and allow ten minutes.

Drying time is extra, and only matters if liquid is involved. If the phone got wet, run Water mode first, then let it air dry before you plug in a charger. Apple advises waiting at least 30 minutes before charging a wet iPhone. If you used a barely damp brush on a sticky grille, let the grille dry for about an hour before the sound steps.

From dirty grille to clean speaker in eight steps

  1. Take off the case and wipe the phone with the dry microfiber cloth.
  2. Find the holes. The loudspeaker is on the bottom edge or the side. The earpiece is the thin slot at the top of the screen. Shine the flashlight across each one at an angle and note what you see: lint, grey fuzz or a shiny film.
  3. Hold the phone with the bottom speaker facing down. Brush across the holes with short, light strokes, then tap the phone against your palm to drop out loose dust.
  4. Turn the phone around so the earpiece faces down and brush that slot the same way, even more lightly.
  5. Set the volume to maximum, switch off silent mode and press Start in Dust mode with the bottom speaker facing down. Let all 60 seconds play.
  6. For the earpiece, switch to Ear speaker mode and run its 45 seconds with the earpiece facing down. Some phones use the earpiece only for calls. If you hear nothing from it, skip this step.
  7. Dab each grille once with a fresh piece of tape or putty and pull it straight off. Never push it into the holes.
  8. Play a song or the speaker test at about 70 percent volume and compare. If it still sounds dull, repeat from step 3 one more time.

Dust cleaner sound

Keeping the speaker clean afterwards

Most of the dirt comes from where the phone lives. A loose pocket packs lint into the grille, and a bag collects fine dust. A case that covers the grille with a thin flap of plastic or a tight cutout traps debris against the holes, so lift the case off now and then and check underneath.

Carry the phone in a pocket with nothing loose, or use a case with a clear, open cutout. A quick dry brush every few weeks stops build-up from packing down. Brush before you notice a problem, not after the volume has already dropped.

When cleaning is not the answer

Cleaning only reaches the outside of the grille and the first bit behind it. If the sound is no better after two full rounds, look elsewhere. Check the case, Bluetooth output and volume settings first.

If you hear a rattle or a buzz at normal volume, the mesh is torn or dented, or there is green or white residue on the grille, take it to a repair shop. For a deeper look at tools to use and avoid, read the full dust guide.

Read the dust cleaning guide

Questions people ask

Should the phone be switched off while I brush?

Not required, but switching it off prevents accidental taps. Turn it back on before the sound steps, because the cleaner runs in your browser and needs the phone awake.

What is the safest brush to use on a phone speaker?

A clean, dry toothbrush with soft bristles, or a soft makeup brush. Avoid stiff or worn bristles. If you can feel the bristles scratching your skin, they are too hard for the mesh.

Should I start with Dust mode or Water mode?

Start with Dust mode if the speaker is muffled but the phone never got wet. Use Water mode only after a splash or a dip. Both are free, but running the wrong one just wastes a minute.

Will the speaker sound louder straight after the first run?

Sometimes. A lightly dusty speaker can improve right away, while a packed one needs brushing between runs. Compare using the same song at the same volume, rather than judging from memory.

Do I need to clean the earpiece as well as the bottom speaker?

Clean it if calls sound quiet or if your phone plays media through the earpiece too. The earpiece collects skin oil and makeup, so brush it lightly and keep the pressure even lower than on the bottom grille.

More cleaning tools