Skip to the tool
Speaker Cleaner

Clear My Speaker

Check the grille with a flashlight, then press Start in Dust mode with the speaker facing down. If the blockage looks sticky, clear the surface first.

200Hz

Ready

60seconds left

A rising sweep from 200 to 1200 Hz that shakes loose dry dust and lint. 60 seconds.

Set volume to maximum, turn off silent mode, and hold the phone with the speaker facing down.

Disconnect Bluetooth headphones first, otherwise the sound plays there instead of the phone speaker.

Check the result

Play each side. A clean speaker sounds clear and equally loud on both channels.

What clogs a phone speaker grille

  • Pocket lint, which packs into the holes a little more every day
  • Fine dust and sand from bags, beaches, building sites and car dashboards
  • Makeup and skin oil, especially around the earpiece
  • Dried residue from soda, coffee, sweat or salt water, which leaves a hard crust on the mesh

Symptoms you can hear and see

  • The volume has dropped and turning it up does not help much
  • Voices and music sound thin, tinny or far away
  • The grille looks grey or fuzzy under a flashlight
  • One speaker is quieter than the other on a stereo phone
  • A buzz or rattle at certain notes

Check the grille with a flashlight and a test

Shine a flashlight, such as the one on a second phone, across the grille at a low angle. Clean mesh looks dark and open. A blocked one looks grey, fuzzy or covered with a shiny film or crust.

Then run the speaker test below the cleaner at about 70 percent volume. Play Left, then Right, then Both, and then the Full sweep. Notice whether one side is clearly quieter or a note buzzes. A phone with one mono speaker plays Left and Right from the same place, which is normal.

Clearing it safely, depending on what is in there

Dry debris and sticky residue need different treatment. Decide which one you have from the flashlight check, then follow the steps.

  1. Take off the case, disconnect Bluetooth, switch off silent mode and set the volume to maximum.
  2. Hold the phone with the speaker facing down.
  3. For dry debris such as lint, dust or sand, brush across the holes with a soft dry brush, then tap the phone against your palm.
  4. For sticky residue, dip only the tips of a soft brush in fresh water, blot them until barely damp, and brush the surface of the grille. Never pour or spray water on the speaker.
  5. Let the phone dry completely, which takes about an hour if you used any moisture.
  6. Press Start in Dust mode and let all 60 seconds play. If the grille is still stubborn, run Deep clean once, which takes 2 minutes.
  7. Dab the grille lightly with fresh tape or putty, then run the speaker test again and compare.

When the blockage is behind the mesh

Sound and brushing only reach the outside of the grille and a short way in. If debris has gone behind the mesh, or liquid has dried inside the phone, nothing done from outside will clear it. Only a repair shop can open the phone, clean it and replace the speaker if it has been damaged.

Signs that the problem is inside: the grille looks clean but the sound is still thin, the sound is unchanged after two full rounds, or you hear a rattle at every volume. Go through the other causes of a quiet speaker before you book a repair.

Read the muffled speaker guide

Questions people ask

Why does only one of my two speakers sound blocked?

Stereo phones have two separate openings, usually the bottom grille and the earpiece slot, and they collect dirt at different rates. The one that carries more lint or skin oil sounds quieter. Clean the dirtier one, then run the test again.

Can sand in the grille be shaken out with sound?

Fine, loose sand sometimes works its way out with the speaker facing down. Coarse grains lodged in the holes will not. Brush the surface gently, and do not scrape. Sand scratches the mesh if you press it.

How damp is too damp when clearing sticky residue?

If you can see water on the brush, it is too wet. Touch the tips to fresh water, then blot them on a paper towel until they feel almost dry. The aim is to soften the crust on the surface, not wet the mesh.

Should I use Dust mode or Deep clean for a stubborn blockage?

Start with Dust mode, which is built for fine dust and lint. Use Deep clean if the grille still sounds dull after brushing and one Dust run. It takes 2 minutes and adds a water pulse and short square-wave bursts.

The grille looks clean but the sound is still thin. Why?

The cause may be behind the mesh, in a setting, or in the hardware. Check the case, Bluetooth output and sound settings first. If none of those help, a repair shop can look inside the phone.

More cleaning tools