Skip to the tool
Speaker Cleaner

Sound to Clean Speaker

Set a frequency and a wave in Manual mode, then press Start. The sections below tell you which settings suit which problem.

165Hz

Ready

300seconds left

Pick your own frequency and wave shape. Stops on its own after 5 minutes.

Set volume to maximum, turn off silent mode, and hold the phone with the speaker facing down.

Disconnect Bluetooth headphones first, otherwise the sound plays there instead of the phone speaker.

Check the result

Play each side. A clean speaker sounds clear and equally loud on both channels.

Set up a manual run in seven steps

  1. Remove the case, disconnect Bluetooth and switch silent mode off.
  2. Hold the phone with the speaker grille facing the floor.
  3. Choose Manual mode. The slider starts at 165 Hz.
  4. Pick a wave. Use Sine for a first run.
  5. Move the slider to the frequency that suits your problem, using the list below.
  6. Set the volume to maximum, keep the phone away from your ears and press Start. Watch the Hz display and the countdown.
  7. Stop after 30 to 60 seconds, dab the grille, check the sound and rest before the next run.

Four waves, four textures

Square and Saw sound much louder than Sine, so the tool plays them at a lower level. That is why they do not feel twice as loud as Sine even though they carry more energy. Start with Sine for water, and try Saw or Square for dust only after a sweep has not helped. A buzzier wave is not a stronger clean, only a different texture.

  • Sine: one smooth, pure pitch. The best first choice for water.
  • Triangle: slightly brighter than Sine, with a few more overtones.
  • Square: buzzy and hollow, with many overtones.
  • Saw: buzzy and bright, also with many overtones. Dust mode uses this wave.

Which Hz suits which problem

  • Water on a phone: about 150 to 200 Hz. Leave the slider at 165 Hz if unsure.
  • Tablets and laptops: 100 to 140 Hz. Larger speakers can play lower notes with force.
  • Dust: try several points between 200 and 1000 Hz, holding each for ten seconds or so. Or just use Dust mode, which sweeps for you.
  • Earpiece: use a higher setting, such as 400 to 1000 Hz, and keep the wave on Sine. Ear speaker mode does this with a gentle sweep and goes up to 1500 Hz.
  • Avoid the very bottom of the slider on a phone. A tiny speaker cannot play 80 Hz loudly and may only buzz.

Volume, rattle and rest between runs

For cleaning, use maximum volume for short runs. If the sound turns into a harsh rattle, back off a little, because the case, a loose part or a damaged cone may be rattling. Never hold the phone near your ears while a tone plays.

Manual mode stops on its own after 5 minutes, but most jobs do not need that long. Rest for a minute between runs, dab the grille and test before you start again.

Keep the changes small. Moving the slider by a few Hz at a time makes it easier to hear which setting gives the clearest result, and it stops you guessing. If three or four runs at different settings change nothing, the cause is probably not water or dust. A repair shop is the right next step.

When to leave the slider alone

If you do not know the problem, a preset is easier. Water, Dust, Deep clean and Ear speaker already combine a frequency, a wave and a time. Use Manual when a preset did not help, or when you want to try a particular pitch.

Phone speaker cleaner soundWhat about 10,000 Hz?

Questions people ask

Why does Square sound louder than Sine at the same slider position?

A square wave carries more energy across many overtones, so it sounds much louder. The tool plays Square and Saw at a lower level to make up for that.

My slider is at 80 Hz and I hear only a buzz. Is something broken?

Probably not. A phone speaker is too small to play 80 Hz well, so you hear the cone struggling. Move up to about 150 Hz or more.

How low should I set the slider on a tablet?

Try 100 to 140 Hz. Tablets have larger speakers than phones, so they can play lower notes with more force.

How long can a Manual run last?

Up to 5 minutes, then it stops on its own. For cleaning, 30 to 60 seconds followed by a check is usually enough.

Is a higher Hz better for dust?

Not necessarily. Dust sits in the mesh in uneven ways, so variety matters more than one high note. Try several points between 200 and 1000 Hz, or let Dust mode sweep for you.

More cleaning tools