Skip to the tool
Speaker Cleaner

Speaker Cleaning Sound

Press Start on Deep clean to hear all three tone types in two minutes. The sections below explain what each one is doing.

165Hz

Ready

120seconds left

Low pulse, sweep and burst phases back to back for stubborn blockage. 2 minutes.

Set volume to maximum, turn off silent mode, and hold the phone with the speaker facing down.

Disconnect Bluetooth headphones first, otherwise the sound plays there instead of the phone speaker.

Check the result

Play each side. A clean speaker sounds clear and equally loud on both channels.

How a speaker cone moves, and where phones hit a floor

A speaker makes sound by moving a thin cone back and forth. Each push and pull moves the air in front of it, and your ear hears that as a tone. A low tone means slow, wide movements. A high tone means fast, small ones.

For the same loudness, a low note makes the cone travel further. That is useful for cleaning, because a cone that moves more shakes the air and anything sitting in the grille. But a phone speaker is tiny and has very little room to move. Go much lower and it struggles to play loudly, and near the bottom of the range it may only buzz. Around 165 Hz is a practical low point for phones: low enough for long cone travel, high enough that the speaker can still play it with some force. Tablets and laptops have larger speakers and can go lower.

Why the water tone pulses

Water mode does not hold one note. It plays about half a second of 165 Hz, a short dip, then repeats. One reasonable explanation is that the dips give the cone and the water surface a moment to rebound, so each new push meets water that has moved instead of water that is being pushed all the time.

Treat that as a model, not a proof, since nobody can see inside your phone. The thing you can check is the result: droplets or damp marks on the cloth when you dab the grille, and a clearer sound afterwards.

Sweep, sawtooth and earpiece: the other tones

Dust is loose and uneven. A single pitch may shake some grains and miss others, so Dust mode glides between 200 and 1200 Hz and passes through many pitches. It uses a sawtooth wave, which has more overtones than a sine wave, so it is buzzier and puts energy into several pitches at once.

The earpiece is a smaller part built for speech. Ear speaker mode uses a gentler sine sweep between 400 and 1500 Hz, so it gets a higher range and a softer wave.

Every mode with its exact numbers

  • Water: 165 Hz sine tone, pulsed, for 60 seconds.
  • Dust: sawtooth sweep between 200 and 1200 Hz, one up-and-down cycle every 6 seconds, for 60 seconds.
  • Deep clean: 2 minutes in three phases. 0 to 40 s is the 165 Hz water pulse. 40 to 90 s is a sawtooth sweep between 100 and 800 Hz. 90 to 120 s is short square-wave bursts alternating between 140 and 220 Hz.
  • Ear speaker: sine sweep between 400 and 1500 Hz, one cycle every 5 seconds, for 45 seconds.
  • Manual: slider from 80 to 1000 Hz, starting at 165 Hz, with Sine, Square, Saw or Triangle waves. It stops on its own after 5 minutes.

Running Deep clean, phase by phase

Deep clean suits a phone that sounds dull and also looks dusty, or when you cannot tell which problem you have.

  1. Wipe the phone, remove the case, disconnect Bluetooth, switch silent mode off and set the volume to maximum.
  2. Hold the phone with the speaker grille facing the floor, choose Deep clean and press Start. The countdown shows the 120 seconds.
  3. 0 to 40 s: the water pulse. This is the same 165 Hz pulse as Water mode, aimed at water in the mesh.
  4. 40 to 90 s: the sawtooth sweep from 100 to 800 Hz. It sounds buzzier and slides up and down. It is aimed at loose dust.
  5. 90 to 120 s: short square-wave bursts alternating between 140 and 220 Hz. Square waves are played at a lower level because they sound much louder.
  6. Dab the grille with a dry cloth, then play a song to judge the result. Rest a minute before a second run.

Why 165 Hz is usedWhat about 10,000 Hz?

Questions people ask

Does a lower frequency always clean better?

No. A lower note moves the cone further, but a tiny phone speaker cannot play deep notes loudly. Well below 165 Hz it may only buzz, so more bass is not better on a phone.

Why does Deep clean sound harsher in the last phase?

The last phase uses square-wave bursts, and a square wave has a lot of overtones. It is played at a lower level, but it still sounds sharper than the sine tone at the start.

Why does Water mode stop and start instead of playing one note?

The pulse has a short dip after each half second of tone. The dip is thought to let the cone and the water rebound before the next push. It is part of how the mode is built, not a fault.

Do I need Deep clean, or is Water or Dust mode enough?

Water or Dust mode is enough when you know the problem. Deep clean is for unclear cases, or when a single mode did not change the sound.

Does the waveform display show that cleaning is working?

No. It only shows the sound being played. Judge the result by ear, and by what comes out onto the cloth.

More cleaning tools