Skip to the tool
Speaker Cleaner

Speaker Sound

Press Left, Right, Both and Full sweep in the test panel, then use the Manual slider below as a steady tone. Listen first, clean second.

165Hz

Ready

300seconds left

Pick your own frequency and wave shape. Stops on its own after 5 minutes.

Set volume to maximum, turn off silent mode, and hold the phone with the speaker facing down.

Disconnect Bluetooth headphones first, otherwise the sound plays there instead of the phone speaker.

Check the result

Play each side. A clean speaker sounds clear and equally loud on both channels.

A five-step listening routine

A speaker problem is easier to fix once you know what kind it is. This routine takes about two minutes.

  1. Disconnect Bluetooth, switch silent mode off and set the volume to about 70 percent. Full volume can hide a rattle behind distortion.
  2. Press Left, then Right, then Both. Each plays a 440 Hz tone for about 2.5 seconds. On a phone with one mono speaker, Left and Right come from the same place, which is normal.
  3. Press Full sweep. It glides from 20 Hz to 20,000 Hz over about 14 seconds. Listen for gaps, buzzing and sudden drops in volume.
  4. Use the Manual slider on Sine and hold it at 165 Hz, then at a few other points such as 300 and 600 Hz. A steady tone makes a rattle easy to hear. Keep the phone away from your ear.
  5. Finish with a song you know well, with vocals and some bass. Listen for thin voices, missing bass or crackle.

What a healthy speaker sounds like

A healthy speaker plays the 440 Hz tone as a clean, steady note with no hiss, no buzz and no wobble. Left and Right match in loudness, or both come from the same place on a mono phone.

In the full sweep you should hear the pitch rise smoothly. A phone speaker cannot play the lowest part, so the first second or two may be silent or faint. Most adults also stop hearing the sweep somewhere in the high thousands. Both are normal and say nothing about damage.

Three problems, three different sounds

  • Water-blocked: dull and muffled, like the phone is underwater. Voices lose their edge and the volume drops. The tone sounds soft instead of sharp, and it may gurgle or crackle at first.
  • Dust-blocked: thin and quiet. Bright sounds and bass both seem weaker, and you may hear a buzz at certain notes that comes and goes as the slider moves.
  • Damaged: crackle at every volume and every frequency, a rattle that does not change, or nothing at all from one side. Cleaning will not cure this.

Using the Manual slider as a steady test tone

The slider runs from 80 to 1000 Hz and starts at 165 Hz. Sine gives the cleanest tone, so use it for judging. Square and Saw are buzzy on purpose and make poor test tones.

If a spot on the slider sounds rough while the rest is smooth, move a little either way. A buzz that appears only at one note is often a loose part or a partly blocked grille. A rough sound at every point points to damage. Manual mode stops on its own after 5 minutes.

What to do with what you heard

Dull or thin sound with no crackle suggests a blocked grille. Try Water or Dust mode and test again. Crackle at all volumes, even after cleaning, points to a damaged cone or a loose connector, which needs a repair shop.

How to test a phone speaker

Questions people ask

Why does the test use 440 Hz?

It is the pitch of the A above middle C, a common reference note. Nearly every phone speaker can play it clearly, so a poor result is a useful warning.

Why can I not hear the start or the end of the full sweep?

Phone speakers are too small to play the lowest notes. Your ears also stop hearing very high pitches, and most adults lose them somewhere in the high thousands of Hz. Both are normal.

Which wave should I choose for listening tests?

Sine. It is a single smooth pitch, so any buzz you hear comes from the speaker and not from the sound itself.

What volume should I use when judging a speaker?

About 70 percent. At full volume, distortion can cover a rattle. Save maximum volume for cleaning runs.

Can I tell water from dust just by listening?

Often, but not always. Water gives a dull, underwater sound. Dust gives a thin, quiet sound with buzz at certain notes. If you cannot tell, try Water mode first, then Dust mode, and test after each.

More cleaning tools